[GSBN] Modeling or measuring mass effect of interior plaster

Tue May 7 01:05:33 UTC 2013

Hi All

This is a note that has been published by the Australian Institute of
Architects regarding Thermal Mass.

I thought that you may find this interesting? Any comments John?? Laura??

Regards

Bohdan Dorniak

From: GSBN-bounces at sustainablesources.com
[mailto:GSBN-bounces at sustainablesources.com] On Behalf Of John Swearingen
Sent: Tuesday, 7 May 2013 9:38 AM
To: Global Straw Building Network
Subject: Re: [GSBN] Modeling or measuring mass effect of interior plaster

Laura,

Modeling thermal mass is generally difficult because of the large variable
conditions of heat transfer related to air circulation. We've done this in
Energy-10 with some success, and usually our projections have come out on
the conservative side--the temperature swings have been less than we
calculated. 

The other very large variable is climate--temperatures and sunshine at
different times of the year. Everyone I know who does this successfully had
dialed it in from years of experience in one particular climate, with which
they are familiar.

As to whether the walls make a difference,  the short answer is, I think it
makes a big difference, and that many of the lauded characteristics of
thermal comfort in straw bale buildings may have as much to do with the
thermal mass on the walls as with the insulation.  Modulated temperature
swings can influence occupant behavior positively, reducing reliance on
mechanical systems, over and above straight Btu calculations.

The ultimate efficiency of thermal mass is tied to the heat-transfer
mechanism for exchanging heat between the mass and the rest of the building
(air).  A floor slab is thick and of limited surface area; bale walls are
thin with a much larger surface area. So floor slabs are longer term
storage, and walls  function very effectively to modulate temperature swings
on a short term (diurnal) cycle which can reduce loads on mechanical systems
and increase comfort in passive buildings.  I don't think there is too much
danger of over-massing, and haven't seen it in our buildings, because the
relatively thin mass of the walls, backed by insulation and actively
transferring heat, stays close to room temperature and so isn't felt as too
cold or hot.

Temperature modulation can result in significant changes in how mechanical
heating and cooling are used by the occupants: if the building is slow to
cool off at night, for instance, the occupants don't call for heat early in
the evening.  The key here is responsiveness, which is related to surface
area. Mass walls also help to distribute Btu's somewhat between warmer and
cooler areas of the building: cooler walls will absorb heat more readily
than warm walls, so they are somewhat of a magnet for warm air when located
in cooler areas of the building.  

Well, hope this helps!

John.

On Mon, May 6, 2013 at 12:39 PM, Laura Bartels <laura at greenweaver.com>
wrote:

Hello All,

I'm writing to ask if anyone has had experience with modeling or measuring
the mass effect of interior plaster of bale walls versus other interior
finishes. This has come up on a straw bale project in design phase I've
involved in which has a net zero energy goal. The project is large, about
6000 sf. The owners are interested in  barnwood interior wall surfaces (over
plaster) on all or some walls. With the net zero goal, the question is what
we might lose in having wood rather than exposed plaster. There will be
adobe floors which will already provide direct and indirect gain mass.  

Anyone tackled this topic or have a guess about how to look at this? Our
team has talked about estimating direct vs. indirect gain wall surfaces
through sun studies in ArchiCAD as a starting point. 

Looking forward to hearing any thoughts on this.

Laura

Laura Bartels

GreenWeaver Inc.

520 S. Third St., Suite 5 

Carbondale, CO 81623
970-379-6779
www.greenweaverinc.com

_______________________________________________
GSBN mailing list
GSBN at sustainablesources.com
http://sustainablesources.com/mailman/listinfo.cgi/GSBN

-- 
John Swearingen
Skillful Means Design & Construction
2550 9th Street   Suite 209A
Berkeley, CA   94710
510.849.1800 phone
510.849.1900 fax

Web Site:  http://www.skillful-means.com
Blog:         https://skillfulmeansdesign.wordpress.com 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sustainablesources.com/pipermail/gsbn/attachments/20130507/47ece083/attachment.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 3970 bytes
Desc: not available
URL: <http://lists.sustainablesources.com/pipermail/gsbn/attachments/20130507/47ece083/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: EDG_76_AuSES-2_Tas_ThermaL_Mass.pdf
Type: application/pdf
Size: 467477 bytes
Desc: not available
URL: <http://lists.sustainablesources.com/pipermail/gsbn/attachments/20130507/47ece083/attachment.pdf>