[GSBN] Straw Bale Cutting Tool - Any Ideas

[Derek Roff]

When we built the demonstration Eco-House at the US Botanical Garden in Washington, DC, we used Sam Droege’s Wood Mizer bandsaw lumber mill.  It’s similar to the one shown in Chris’s pictures.  It worked very well, for both sizing bales and getting a smoother surface on the “cut side” of the bales, which makes plastering easier.

The cut side of bales from many suppliers has ripples that are pretty deep.  If I owned a bandsaw mill, I would consider trimming all the bales with an uneven cut side, so that the plaster would end up with a much more even thickness.

Derek

Derek Roff
derek at unm.edu<mailto:derek at unm.edu>




On Sep 13, 2017, at 9:32 AM, Chris Magwood <chris at endeavourcentre.org<mailto:chris at endeavourcentre.org>> wrote:


A photo, to elaborate...

On 2017-09-13 11:20 AM, David Arkin, AIA wrote:
Hello Global Straw Balers:

CASBA has a workshop coming up, fitting bales between studs in a large three-story office building.  While many of the stud bays are 22 1/2” wide, set to easily fit 23” wide bales on end, many other bays are of lesser dimensions, requiring the ripping of the bales to a narrower width.

We’ve successfully used electric chain saws to rip an occasional bale during bale-raisings, but the scale of this project suggests a better tool for this task.  One solution we’ve been mulling is a bandsaw (pic attached, covers off).  Thoughts on the pros & cons of this approach welcome.

Wondering if anyone out there has found or devised a good tool for this task?  I searched the archives (thanks again Bill) and didn’t come up with any prior discussion on this topic, surprisingly.

Thanks all,

David ‘must get ripped’ Arkin / ATA & CASBA

<IMG_9674.jpeg>

On Sep 12, 2017, at 6:32 PM, Bill Christensen <billc_lists at greenbuilder.com<mailto:billc_lists at greenbuilder.com>> wrote:

Yes, our archives (nearly 30 years worth!) can be a lot to sift through!  The good news is that a) the search engines regularly index the archives and b) there are very few other instances of our subject line identifier,  "[GSBN]", out there.

Go to Google or your other favorite search engine

Enter: [GSBN] followed by the topic/keyword(s) of your choice

for instance:

[GSBN] clay paint

or
[GSBN] chemical sensitivity

et voila, lots of results without digging through 30 years worth of posts.
_______________________________________________
Gsbn mailing list
Gsbn at sustainablesources.com<mailto:Gsbn at sustainablesources.com>
http://sustainablesources.com/mailman/listinfo.cgi/gsbn

*  *  *  *  *
Arkin Tilt Architects
Ecological Planning & Design
1101 8th St. #180, Berkeley, CA  94710
510/528-9830 ext. 2#
www.arkintilt.com<http://www.arkintilt.com/>

David Arkin, AIA, Architect
LEED Accredited Professional
CA #C22459/NV #5030

Director, California Straw Building Association
www.strawbuilding.org<http://www.strawbuilding.org/>
CASBA is a project of the Tides Center

"There is no way to peace. Peace is the way."
— A. J. Muste









_______________________________________________
Gsbn mailing list
Gsbn at sustainablesources.com<mailto:Gsbn at sustainablesources.com>
http://sustainablesources.com/mailman/listinfo.cgi/gsbn



--
Chris Magwood
Director, Endeavour Centre
www.endeavourcentre.org<http://www.endeavourcentre.org/>

<DSC01172.jpg>_______________________________________________
Gsbn mailing list
Gsbn at sustainablesources.com<mailto:Gsbn at sustainablesources.com>
http://sustainablesources.com/mailman/listinfo.cgi/gsbn

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sustainablesources.com/pipermail/gsbn/attachments/20170913/a23f228a/attachment.htm>