<div dir="ltr">I don't know how much different Cintoflex C is from D, but our experience with Cintoflex C was not great.  It was really challenging to tension well, and efforts to "quilt" it with galvanized through pins from the outside to the inside regularly broke the mesh.  The same was true for inside corners and other similar details.  I remember it sagging in places if, because of irregularities, scratch coat was thicker and heavier.  It didn't seem to be an improvement over good ol' galvanized stucco lathe.<div><br></div><div>Misha Rauchwerger</div><div>Built in Bliss Construction</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Sat, Oct 1, 2016 at 2:29 AM, Rene Dalmeijer <span dir="ltr"><<a href="mailto:rene.dalmeijer@hetnet.nl" target="_blank">rene.dalmeijer@hetnet.nl</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Chris,<br>
<br>
I have been using jute extensively, exclusively  for interior walls.<br>
<br>
Depending on the jute and the state of the earth plaster, it can very from an uphill struggle to a piece of cake. The best experiences we have are with a stiffened 10mm mesh jute used dry, in a really wet, before last layer. Preferably it is a two person job one prepares the full wall height (-50mm) strips our roll is 1.2m wide althoughI have also used 2m. Seems are overlapped roughly 50mm. One holds up the two top corners and the other uses a steel float (with rounded corners) to press it in. Once the whole strip is in we rub it in with a wooden float, adding some water and maybe a little fresh earth plaster to just cover the mesh.<br>
<br>
On a recent project we used polyester 8mm mesh basically it is easier to use due to its inherent stiffness. On the same project we had to fill out a really crooked wall 70mm. We used a stainless mesh attached to the wooden subframe to ensure there would be no mechanical problems as the plastered wall is 7.5m tall.<br>
<br>
<br>
Rene Dalmeijer Proces Advies<br>
Thomas Hoodstraat 2<br>
1086 WE Amsterdam<br>
<br>
06 48955419<br>
<br>
KvK 34243755<br>
BTW NL057444146B01<br>
NL18ASNB0932817343<br>
<br>
IBAN NL09INGB0004388720<br>
BIC INGBNL2A<br>
<div class="HOEnZb"><div class="h5"><br>
On Aug 12, 2016, at 01:06, Chris Magwood wrote:<br>
<br>
> Hi all,<br>
><br>
> For the first time in a long time, I'm in the market for some mesh for our jumbo straw bale project this summer. The sources we've used in the past have all dried up and our inventory is empty.<br>
><br>
> So I thought it might be a good time to check in and see what others have been using. We're not looking to cover the entire wall, but we have some significant amounts of framing that need bridging, and ideally we'd prefer not to use metal mesh. I'd love to know what any of you are currently using and where you're sourcing it and perhaps refresh our practice a bit!<br>
><br>
> Thanks!<br>
><br>
> Chris<br>
><br>
><br>
> --<br>
> Chris Magwood<br>
> Director, Endeavour Centre<br>
> <a href="http://www.endeavourcentre.org" rel="noreferrer" target="_blank">www.endeavourcentre.org</a><br>
><br>
> ______________________________<wbr>_________________<br>
> Gsbn mailing list<br>
> <a href="mailto:Gsbn@sustainablesources.com">Gsbn@sustainablesources.com</a><br>
> <a href="http://sustainablesources.com/mailman/listinfo.cgi/gsbn" rel="noreferrer" target="_blank">http://sustainablesources.com/<wbr>mailman/listinfo.cgi/gsbn</a><br>
<br>
______________________________<wbr>_________________<br>
Gsbn mailing list<br>
<a href="mailto:Gsbn@sustainablesources.com">Gsbn@sustainablesources.com</a><br>
<a href="http://sustainablesources.com/mailman/listinfo.cgi/gsbn" rel="noreferrer" target="_blank">http://sustainablesources.com/<wbr>mailman/listinfo.cgi/gsbn</a><br>
</div></div></blockquote></div><br></div>